Volcanic ash

Volcanic ash consists of fragments of pulverized rock, minerals and volcanic glass, created during volcanic eruptions and measuring less than 2 mm (0.079 inches) in diameter. The term volcanic ash is also often loosely used to refer to all explosive eruption products (correctly referred to as tephra), including particles larger than 2mm. Volcanic ash is formed during explosive volcanic eruptions when dissolved gases in magma expand and escape violently into the atmosphere. The force of the escaping gas shatters the magma and propels it into the atmosphere where it solidifies into fragments of volcanic rock and glass. Ash is also produced when magma comes into contact with water during phreatomagmatic eruptions, causing the water to explosively flash to steam leading to shattering of magma. Once in the air, ash is transported by wind up to thousands of kilometers away.Due to its wide dispersal, ash can have a number of impacts on society, including human and animal health, disruption to aviation, disruption to critical infrastructure (e.g., electric power supply systems, telecommunications, water and waste-water networks, transportation), primary industries (e.g., agriculture), buildings and structures.

Formation

Volcanic ash is formed during explosive volcanic eruptions, phreatomagmatic eruptions and during transport in pyroclastic density currents.

Explosive eruptions occur when magma decompresses as it rises, allowing dissolved volatiles (dominantly water and carbon dioxide) to exsolve into gas bubbles. As more bubbles nucleate a foam is produced, which decreases the density of the magma, accelerating it up the conduit. Fragmentation occurs when bubbles occupy ~70-80 vol% of the erupting mixture. When fragmentation occurs, violently expanding bubbles tear the magma apart into fragments which are ejected into the atmosphere where they solidify into ash particles. Fragmentation is a very efficient process of ash formation and is capable of generating very fine ash even without the addition of water.

Volcanic ash is also produced during phreatomagmatic eruptions. During these eruptions fragmentation occurs when magma comes into contact with bodies of water (such as the sea, lakes and marshes) groundwater, snow or ice. As the magma, which is significantly hotter than the boiling point of water, comes into contact with water an insulating vapor film forms (Leidenfrost effect). Eventually this vapor film will collapse leading to direct coupling of the cold water and hot magma. This increases the heat transfer which leads to the rapid expansion of water and fragmentation of the magma into small particles which are subsequently ejected from the volcanic vent. Fragmentation causes an increase in contact area between magma and water creating a feedback mechanism,  leading to further fragmentation and production of fine ash particles.

Pyroclastic density currents can also produce ash particles. These are typically produced by lava dome collapse or collapse of the eruption column.  Within pyroclastic density currents particle abrasion occurs as particles interact with each other resulting in a reduction in grain size and production of fine grained ash particles. In addition, ash can be produced during secondary fragmentation of pumice fragments, due to the conservation of heat within the flow. These processes produce large quantities of very fine grained ash which is removed from pyroclastic density currents in co-ignimbrite ash plumes.

Physical and chemical characteristics of volcanic ash are primarily controlled by the style of volcanic eruption.[8] Volcanoes display a range of eruption styles which are controlled by magma chemistry, crystal content, temperature and dissolved gases of the erupting magma and can be classified using the volcanic explosivity index (VEI). Effusive eruptions (VEI 1) of basaltic composition produce <105 m3 of ejecta, whereas extremely explosive eruptions (VEI 5+) of rhyolitic and dacitic composition can inject large quantities (>109 m3) of ejecta into the atmosphere. Another parameter controlling the amount of ash produced is the duration of the eruption: the longer the eruption is sustained, the more ash will be produced. For example, the second phase of the 2010 eruptions of Eyjafjallajökull was classified as VEI 4 despite a modest 8 km high eruption column, but the eruption continued for a month, which allowed a large volume of ash to be ejected into the atmosphere.

Chemical

The types of minerals present in volcanic ash are dependent on the chemistry of the magma from which it erupted. Considering that the most abundant elements found in silicate magma are silicon and oxygen, the various types of magma (and therefore ash) produced during volcanic eruptions are most commonly explained in terms of their silica content. Low energy eruptions of basalt produce a characteristically dark coloured ash containing ~45 - 55% silica that is generally rich in iron (Fe) and magnesium (Mg). The most explosive rhyolite eruptions produce a felsic ash that is high in silica (>69%) while other types of ash with an intermediate composition (e.g., andesite or dacite) have a silica content between 55-69%.

The principal gases released during volcanic activity are water, carbon dioxide, sulfur dioxide, hydrogen, hydrogen sulfide, carbon monoxide and hydrogen chloride. These sulfur and halogen gases and metals are removed from the atmosphere by processes of chemical reaction, dry and wet deposition, and by adsorption onto the surface of volcanic ash.

It has long been recognised that a range of sulfate and halide (primarily chloride and fluoride) compounds are readily mobilised from fresh volcanic ash.;  It is considered most likely that these salts are formed as a consequence of rapid acid dissolution of ash particles within eruption plumes, which is thought to supply the cations involved in the deposition of sulfate and halide salts.

While some 55 ionic species have been reported in fresh ash leachates the most abundant species usually found are the cations Na+, K+, Ca2+ and Mg2+ and the anions Cl−, F− and SO42−. Molar ratios between ions present in leachates suggest that in many cases these elements are present as simple salts such as NaCl and CaSO4. In a sequential leaching experiment on ash from the 1980 eruption of Mount St. Helens, chloride salts were found to be the most readily soluble, followed by sulfate salts  Fluoride compounds are in general only sparingly soluble (e.g., CaF2, MgF2), with the exception of fluoride salts of alkali metals and compounds such as calcium hexafluorosilicate (CaSiF6). The pH of fresh ash leachates is highly variable, depending on the presence of an acidic gas condensate (primarily as a consequence of the gases SO2, HCl and HF in the eruption plume) on the ash surface.

The crystalline-solid structure of the salts act more as an insulator than a conductor.  However, once the salts are dissolved into a solution by a source of moisture (e.g., fog, mist, light rain, etc.), the ash may become corrosive and electrically conductive. A recent study has shown that the electrical conductivity of volcanic ash increases with  increasing moisture content,  increasing soluble salt content, and  increasing compaction (bulk density). The ability of volcanic ash to conduct electric current has significant implications for electric power supply systems.

Adapted from wikipedia.org